Test interne Verres :Échantillons d

Test interne Verres :

Échantillons de 9 Semi finis de bases différentes (4 teintes Transition Brun et 5 Transition Gris)

Valeur de transmission :
Transitions BRUN GRIS
Valeur à l’état clair 91% 92%
Valeur à l’état foncé 16% 17%

! Valeur à l’état foncé mesurée après exposition sous lampe UV pendant 2 min (valeur non optimale)

Contrôle des Semi finis:

L'aspect général est correct mais trop peu de palets pour comparer avec les données techniques (rayon moyen, épaisseur centre)

! Un problème de cylindre sur une base a été constaté (Base 5 Gris)
! Des tensions visibles au tensiscope dans les Semi-Finis

Usinage :

2 paires de verres réalisées :
- 1ère : 2 verres Unifocaux (T7 Brun et T7 Gris)
- 2ème : 1 verre FF (Neo perfect) et 1 progressif FF (Synchrona)

Pas de rayures visibles suite passage Toro-X ou Poli automatique.
Contrôle d’aspect et puissance conformes en sortie de production

! Voir au niveau de la tranche du verre qui est crantée (impact client ?)

Traitement :

Durci : choix de la laque 1,6 + Four 120 - Laque identique utilisée pour les Tribrid ‘classiques’
(Validée avec le traitement)

Traitement : A.R.I et A.R.2 réalisés
Pas de point particulier en sortie traitement. Les tests d’abrasion et d’arrachement sont conformes.
Montage :

Réalisation de tests de détourage sur 2 verres d’épaisseur différentes (E. Bords 10/10e et 25/10e)
Pas de problème pour le meulage et le détourage des verres. Perçage ok.

ผลลัพธ์ (อังกฤษ) 1:

Test internal lenses:Samples of 9 Semi finished of different bases (4 shades Transition Brown and 5 Transition grey)Value of transmission: Transitions Brown greyValue in the clear State 91% 92%Value in the dark state 16% 17%! Dark state value measured after exposure under UV lamp for 2 min (non-optimal value)Control of the Semi finished:The general appearance is OK but too little shuffleboard for compare the technical data (average RADIUS, thick Center)! A problem of cylinder on a basis was found (Base 5 grey)! Visible tensions in the tensiscope in the semi-finishedMachining:2 pairs of glasses made:-1st: 2 single-vision glasses (Brown T7 and T7 grey)-2nd: 1 glass FF (Neo perfect) and progressive 1 FF (Synchrona)No scratches visible suite Toro-X or polished automatic switching.Aspect control and power output of production ! See at the level of the instalment of the glass which is toothed (client impact?)Treatment:Hardened: choice of lacquer 1.6 + oven 120 - identical lacquer used for the 'classics' Tribrid(Validated with treatment)Treatment: A.R.I and A.R.2 madeNo particular point in output processing. Abrasion and pullout tests are consistent.Editing:Testing of clipping on 2 glasses of different thickness (E. edges 10/10 and 25/10)No problem for grinding and trimming of the glasses. Drilling ok.

ผลลัพธ์ (อังกฤษ) 2:

Internal test Glasses: Samples Semi finished 9 different bases (4 colors Brown and Transition 5 Transition Grey) transmission Value: Transitions BROWN GREY value to clear state 91% 92% Value to the dark state 16% 17% ! Value measured in the dark state after exposure under a UV lamp for 2 min (not optimum) Semi finished Control: The general appearance is ok but too few pucks to compare with the technical data (average radius, center thickness) ! A cylinder on a basic problem was found (Base 5 Grey) ! Tensiscope visible tensions in Semi-Finished Machining: 2 pairs of glasses made: - 1st: 2 Single vision lenses (T7 T7 Brown and Grey) - 2nd: 1 glass FF (Neo perfect) and 1 progressive FF (Synchrona) No scratches visible after Toro-X pass or automatic Poli. Aspect control and consistent power output production ! See at the edge of the glass which is notched (client impact?) Treatment: Cast: choice of the lacquer 1.6 + Four 120 - same Laque tribrid used for 'classic' (Validated with treatment) Treatment: ARI and AR2 made ​​no particular point output processing. The abrasion tests and are tearing compliant. Mounting: clipping tests Realization of 2 glasses of different thickness (E. Edges 10 / 10th and 25 / 10th) No problem for grinding and trimming glasses. Drilling ok.

ผลลัพธ์ (อังกฤษ) 3:

Internal test sample cup:

9 finished product library (4 different tones and gray brown transition transition 5)



transfer value: Brown Gray
value state apparent 92%
16%
17%

! Measured values of the state of the deep ultraviolet lamp after 2 min (non optimal value)



control the semi product.The appearance is generally correct, but too many ball comparisons with technical data (average radius, thickness Center)

! On the basis of the problem, the discovery cylinder (base 5 gray)
! Visible in the tensiscope voltage of the semi-finished processing:







2 on the glass: First: 2 cup single focus (T7 T7 brown and gray)
- two:1 cup FF (new perfect and FF (1) gradually synchrona)

no visible fringe etc channel Red Bull X or courtesy of automatic control.! See teeth in glass sheets (affecting customers?)



curing processing:: choose the same as the traditional tribrid 1120 paint paint(verified treatment) treatment: a.r.i


, a.r.2 achieved no point of output processing. The wear and tear are consistent.



: the test was cut to 2 cups (10 / 10. Edge and 10 / 25) with different thicknesses.. Good drilling.